打膠機膠頭堵住的情況進行有效處理
雙組份打膠機的優勢是合理、實際操作簡易等，與此同時因為單單為上膠所涉及所以占地空間小、運作成本費用相比的也是低的，特別適合中小型企業使用。那面對
濟南雙組份打膠機膠頭堵住的情況這么有效處理呢？
The advantages of two-component glue dispenser are reasonable price, simple operation, etc. At the same time, because of the small footprint and low operating costs involved in glue application alone, it is particularly suitable for small and medium-sized enterprises. What if the rubber head of Jinan two-component sealant dispenser is blocked?
由于打膠機由混膠倉到膠嘴容易堵，混膠倉是黑白膠交會(huì )對接的地方，當沖膠黑白分離時黑膠難免不殘留，需然看是沖白了但是這個地方是沖不凈的，這是一道堵，二是由混膠倉到膠嘴，由于要膠在管道走出，管道壁被膠粘得越來越小終堵了，這也是大量想買而不買的原因，有的客戶買了用不了麻煩清洗。
As the glue dispenser is easy to block from the glue mixing bin to the rubber nozzle, the glue mixing bin is the place where black and white glue meets and connects. When the black and white glue is washed and separated, the black glue will inevitably remain. It is necessary to see that the white glue is washed, but this place cannot be cleaned. This is a block. The second is from the glue mixing bin to the rubber nozzle. As the glue is needed to go out of the pipe, the pipe wall is stuck smaller and smaller, and finally blocked. This is also the reason why a lot of people want to buy but do not buy, Some customers bought the car and didn't bother to clean it.
此外一些注意事項也要多加了解，如：
In addition, some precautions should be understood, such as:
1.點膠機不使用膠水時，需要把膠水拿下來保存才可以防止針頭堵塞。例如AB膠，它的固化速度相對來說比較慢，不會(huì )那么快發生堵塞現象，但是如果長時間不操作，還是會(huì )發生堵塞現象的，所以這時候就需要把混合嘴取下，再把膠水保存好，以免堵塞整個出膠針口。
1. When the dispenser does not use glue, it is necessary to take the glue down and save it to prevent the needle from blocking. For example, the curing speed of AB glue is relatively slow, and it will not block up so quickly. However, if it is not operated for a long time, it will still block up. Therefore, it is necessary to remove the mixing nozzle at this time, and then store the glue to avoid blocking the entire rubber outlet.
2.持續點膠時間可以防止針頭堵塞。像瞬干膠來加工點膠產品時，在常溫下快干膠是快速固化的，如果在點膠過程中中斷點膠的話，就很容易把針頭堵塞，所以應該保持點膠的持續工作。
2. The continuous dispensing time can prevent the needle from blocking. For example, when instant drying glue is used to process dispensing products, the instant drying glue is fast curing at room temperature. If the dispensing is interrupted during dispensing, the needle will be easily blocked, so the dispensing should be continued.
3.提高溫度可以防止針頭堵塞。比如熱熔膠使用全不銹鋼點膠針頭，膠水只要加熱就能熔化，所以只要讓加熱器加熱到一定溫度，就不會(huì )發生針頭堵塞現象。
3. Increasing the temperature can prevent the needle from blocking. For example, the hot melt adhesive uses an all stainless steel dispensing needle, and the glue can be melted as long as it is heated, so as long as the heater is heated to a certain temperature, the needle will not be blocked.
4.自動點膠機膠水選料。例如，使用膠水稠度底，不易固化，也不容易出現針頭堵塞現象；粘度高，針頭很快堵塞。
4. Glue selection of automatic dispenser. For example, when using glue with low consistency, it is not easy to solidify, and it is not easy to block the needle; The viscosity is high, and the needle is quickly blocked.
打膠機設計機構科學合理，就生產本身來說因為將中空玻璃的生產環節模式化可以每個生產環節都擁有獨立的機器設備并且相互并不關聯，即便其他機器設備出現問題也不會(huì )對雙組份打膠機的上膠產生影響。您有需求就來我們網站
http://www.sdxfsljx.com留言咨詢并聯系吧！
The sealant dispenser design mechanism is scientific and reasonable. As far as production is concerned, each production link of insulating glass can have independent machines and equipment and are not related to each other. Even if other machines and equipment have problems, the sealant dispensing of two-component sealant dispenser will not be affected. Come to our website if you need http://www.sdxfsljx.com Leave a message to consult and contact!
上一篇：打膠機設計到制作再到出售整個的相關步驟
下一篇：打膠機的液壓缸工作不正常原因及維護
