操作簡單的雙組份打膠機有9個方面要注意
雙組份打膠機控制體系選用PLC和觸屏，人機界面，一鍵式操作。設備操作簡單，方便。廠家告訴大家，操作簡單的雙組份打膠機有9個方面要注意！
The control system of two-component rubber beater adopts PLC and touch screen, man-machine interface and one key operation. The equipment is simple and convenient to operate. The manufacturer told us that there are 9 aspects to pay attention to for the simple two-component sealant dispenser!
1.由于雙組份打膠機的固化需求必定時刻，因此，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. As the curing demand of two-component sealant applicator is certain, the glass coated with two-component sealant should be moved gently horizontally.
2.A組、B組份膠應保持清潔，嚴防異物進入膠中。
2. Group A and B glue shall be kept clean and foreign matters shall be strictly prevented from entering the glue.
3.在連續作業過程中，膠槍每次停止作業時刻一般不得超越20分鐘，不然，運用A組份膠沖出全部混合膠，直單一的A組份膠從槍口排出為止。
3. In the process of continuous operation, the glue gun shall not be stopped for more than 20 minutes each time, otherwise, all the mixed glue shall be flushed out with component A glue until a single component A glue is discharged from the muzzle of the gun.
4.高壓膠管不得強行擠壓、彎曲，避免影響體系正常作業。
4. The high-pressure rubber hose shall not be squeezed or bent by force to avoid affecting the normal operation of the system.
5.混膠器應常常保持暢通，以確保良好的出膠效果。如遇阻塞狀況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. The glue mixer should always be kept smooth to ensure good glue discharging effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to wash every 5 groups.
6.當膠槍長時刻不用時(超越一周)，應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the glue gun is not used for a long time (more than one week), remove the gun body and use solvent to clean the residual colloid in the glue gun and glue mixer.
7.不同雙組份打膠機生產廠家所生產的膠內含雜質數量不同，依據實際狀況清晰B組分的過濾網及單向止回閥，建議每?jì)山M清洗一次。
7. The quantity of impurities in the glue produced by different two-component sealant manufacturers is different. It is recommended to clean the filter screen and one-way check valve of component B according to the actual situation.
8.任何因膠體固化所形成的膠槍、管路或整機的毛病，一律不在保修范圍之內。
8. Any defects of the glue gun, pipeline or the whole machine caused by the gel curing are not covered by the warranty.
9.定期給雙組份打膠機的各個泵的加油口加油，應確保油霧器內不斷油。
9. Fill the oil filler of each pump of two-component sealant dispenser regularly to ensure that there is no oil in the oil atomizer.
The two-component gluing machine is stable and reliable with high production efficiency. When using the two-component sealant machine, pay attention to the above matters. Come to our website for more information http://www.sdxfsljx.com Consult!
上一篇：幾點關于雙組份打膠機的點膠知識要點
下一篇：打膠機工作完后中空膠固化慢怎么回事
