雙組份打膠機平日使用注意以及應用領域
當涉及到打膠機時，其日常維護直接影響到打膠機的使用壽命，所以要想更為長久的順利的使用打膠機進行工作，就要多多在平常中注意一些事項，下面小編為您解析注意事項以及應用領域。
When it comes to the glue dispenser, its daily maintenance directly affects the service life of the glue dispenser. Therefore, if you want to use the glue dispenser successfully for a longer time, you should pay more attention to some matters in daily life. The following sections will explain the matters needing attention and application fields for you.
Notes on daily use of two-component sealant applicator
1.由于雙組份密封膠的固化需要一定時間，因此，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
1. As the curing of two-component sealant takes a certain time, the glass coated with two-component sealant should be moved gently horizontally.
2.A組、B組份膠應保持清潔，嚴防異物進入膠中。
2. Group A and B glue shall be kept clean and foreign matters shall be strictly prevented from entering the glue.
3.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直單一的A組份膠從槍口排出為止。
3. In the continuous working process, the glue gun shall not stop working for more than 20 minutes each time, otherwise, all mixed glue shall be flushed out with component A glue until a single component A glue is discharged from the gun mouth.
4.高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
4. The high-pressure rubber hose shall not be squeezed or bent by force to prevent affecting the normal operation of the system.
5.混膠器應經常保持暢通，以保證良好的出膠效果。如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. The glue mixer shall be kept unblocked to ensure good glue discharging effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to wash every 5 groups.
6.當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
6. When the glue gun is not used for a long time (more than a week), remove the gun body and use solvent to clean the residual colloid in the glue gun and glue mixer.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每?jì)山M清洗一次。
7. The quantity of impurities in the adhesive produced by different two-component adhesive manufacturers is different. The filter screen and one-way check valve of component B should be clear according to the actual situation. It is recommended to clean every two groups.
8.任何因膠體固化所造成的膠槍、管路或整機的故障，一律不在保修范圍之內。
8. Any failure of the glue gun, pipeline or the whole machine caused by the gel curing shall not be covered by the warranty.
9.定期給各泵的加油口加油，應保證油霧器內不斷油。
9. Fill the oil filler of each pump regularly to ensure that there is no oil in the oil atomizer.
雙組份打膠機應用領域
Application field of two-component glue applicator
應用范圍包括各種金屬加工機床的零部件加工，如齒輪箱齒條的裝配和維修，發動機缸體的修理以及軸承的密封和潤滑等。點焊工藝中使用的膠粘劑主要有有機硅膠類和環氧樹脂類兩大類。
The application scope includes parts processing of various metal processing machine tools, such as assembly and maintenance of gear box and rack, repair of engine cylinder block, sealing and lubrication of bearings, etc. Adhesives used in spot welding process mainly include silicone adhesive and epoxy resin.
其中有機硅膠類的膠粘劑有熱熔性橡膠型粘接劑和壓敏性粘接劑兩類；而環氧樹脂類的膠粘劑又可分為厭氧性和氧化固化性?xún)煞N類型。
Among them, there are two kinds of adhesives: hot melt rubber adhesive and pressure-sensitive adhesive; The adhesive of epoxy resin can be divided into two types: anaerobic adhesive and oxidative curing adhesive.
In addition, the daily maintenance of the glue dispenser has a great impact on the service life of the glue dispenser, including the smoothness of common processes. More detailed maintenance methods can be found on our website http://www.sdxfsljx.com consulting service
上一篇：打膠機的產品特點及優勢分析
下一篇：打膠機設備常見的兩個問題以及應對
