自動打膠機分別配置多頭跟單頭的原因
自動打膠機分別配置多頭跟單頭的原因您了解嗎？實際上這個問題應該進行分析，有利于在后期的使用設備工作順順利利，下面
濟南雙組份打膠機廠家為您講解一番吧。
Do you understand the reason why the automatic gluing machine is equipped with multiple heads and single heads? In fact, this problem should be analyzed, which is conducive to the smooth operation of the equipment in the later stage. The Jinan two-component glue machine manufacturer will explain it for you.
選用多頭灌膠的原因：多頭同時灌膠，即可省去三軸走位的時間，假如A設備使用一個頭灌膠，B設備使用四個頭灌膠，那么B設備可以省去三次三軸走位時間，如果生產兩萬的產品，那么省下的時間可以被使用在生產更多的產品上面。
Reasons for selecting multiple heads for glue filling: if multiple heads are used for glue filling at the same time, the time for three-axis movement can be saved. If equipment a uses one head for glue filling and equipment B uses four heads for glue filling, then Equipment B can save three times of three-axis movement time. If 20000 products are produced in a day, the saved time can be used to produce more products.
多頭灌膠，其實就是使用分流器將一個出膠頭的膠水量進行分開灌注。那么需要分流的時候，就會(huì )造成誤差。正負0.1克的誤差便會(huì )提高。某些廠商對于精度要求沒那么高，即便多個0.2克左右膠水，也無傷大雅，但如果追求精度，此時便不可以使用多頭灌膠了。
Multi head glue filling is actually to use a shunt to separate the glue amount of one glue outlet. Then when it is necessary to shunt, it will cause errors. An error of plus or minus 0.1 g is increased. Some manufacturers do not have such high requirements for accuracy. Even if more than 0.2g glue is used, it is not harmful. However, if the accuracy is pursued, it is not allowed to use multiple glue filling at this time.
選用單頭灌膠的原因：既然多頭灌膠對于節約時間如此有用，為何還要選用單頭灌膠呢？不同的廠商會(huì )有不同的灌膠需求。某部分廠商產品的灌膠量特別少，可能在0.5或者0.3克左右，那么此時對于精度要求就特別高，再使用多頭灌膠就不適合了。
Reason for choosing single head glue filling: since multi head glue filling is so useful for saving time, why choose single head glue filling? Different manufacturers have different glue filling requirements. The glue filling amount of some manufacturers' products is very small, which may be about 0.5 or 0.3 g. at this time, the accuracy requirements are particularly high, and it is not suitable to use multiple glue filling.
多頭灌膠之多頭分別控制的打膠機：打膠機分別配置多頭跟單頭，這個功能無需額外增添費用，只需要跟廠家提供一下需求，自會(huì )配備多頭或單頭出膠頭隨機器一起出廠。
Multi head gluing machine controlled by multiple heads: the gluing machine is equipped with multiple heads and single heads respectively. This function does not require any additional cost. It only needs to provide the manufacturer with the requirements, and will be equipped with multiple heads or single head gluing heads to leave the factory with the machine.
但如果是，需要分別控制多個頭的灌膠設備，那么這個需要增添不同的配置。假如配備了四個頭，而這四個頭都是可以使用按鈕分別控制的，也就是可以分別一個，兩個，三個，四個分別或同時出膠水，而是分別為出膠水頭配置泵體，分別計量與控制每個出膠頭的膠水量，從而達到多頭控制的效果，使用分流器進行分流多頭灌膠，則只有同時出膠或不出膠，不能分別控制。
However, if it is necessary to separately control the glue filling equipment of multiple heads, then different configurations need to be added. If there are four heads, and these four heads can be controlled by buttons, that is, one, two, three, four can be used to dispense glue separately or at the same time. Instead, the pump body is configured for the glue dispensing head to measure and control the glue amount of each glue dispensing head respectively, so as to achieve the effect of multi head control. If the diverter is used to dispense glue from multiple heads, the glue can be dispensed at the same time or not, and cannot be controlled separately.
This is the reason why the automatic gluing machine is equipped with multiple heads and single heads. In addition, operators should prevent problems before using the equipment. For more information, please visit our website http://www.sdxfsljx.com Consult and understand.
上一篇：解析打膠機打膠不滿的問題
下一篇：如何做雙組份打膠機的日常維護工作
