關于打膠機的一些問題分析
關于打膠機的使用，很多人都反映使用的效果很好。打膠的效果令人十分滿意，那現階段的打膠機也在不斷的與時俱進的發展，不僅僅是打三玻，更能將四玻打膠。不過打膠機作為玻璃機械設備的一種，也許會(huì )發生些小問題，今兒我們就來說說打膠機的一些問題分析。
As for the use of glue applicator, many people report that the effect of use is very good. The effect of gluing is very satisfactory. At this stage, the gluing machine is also developing with the times. It can not only glue three glasses, but also glue four glasses. However, as a kind of glass mechanical equipment, the glue machine may have some small problems. Today we will talk about some problem analysis of the glue machine.
智能壓力儀表：這方面可能讓很多人表示驚訝，怎么會(huì )呢？這個不可能愛壞。雖然從某種意義上來說，他的使用頻率不會(huì )那么高，不是工人直接接觸的。但是在打膠機的供膠機上有很多的智能壓力儀表，目的就是保證正常的工作進行。所以很難保證每一塊智能壓力表的長久良好運行。智能壓力儀表的，可能要比小吸盤和定位滑輪的稍貴一點。但是因為它的損壞頻率不高，所以還在大家的接受范圍內。
Intelligent pressure instrument: this aspect may surprise many people. How can it be? This can't be bad. Although in a sense, his frequency of use will not be so high, it is not the direct contact of workers. However, there are many intelligent pressure instruments on the glue feeder of the glue dispenser to ensure normal operation. Therefore, it is difficult to ensure the long-term good operation of each intelligent pressure gauge. The price of intelligent pressure instruments may be slightly higher than that of small suction cups and positioning pulleys. However, because its damage frequency is not high, it is still within the range of acceptance.
小零件的損壞：打膠機的小吸盤和定位滑輪的損壞是比較常見的。通常就是單純的由于使用工作時間過長，所以導致的損壞。這些零件在方面也是比較便宜的。
Damage to small parts: damage to the small suction cup and positioning pulley of the gluing machine is common. Usually, it is simply the damage caused by the long working time. These parts are also relatively cheap in price.
膠水流體內產生氣泡：在打膠機使用期間，過大的流體壓力再外部打開點膠閥時，可能將空氣滲入膠水中，從而產生了氣泡。
Bubbles in the glue fluid: during the use of the glue dispenser, when the dispensing valve is opened externally due to excessive fluid pressure, air may penetrate into the glue, resulting in bubbles.
打膠機使用時出現漏膠：點膠閥在使用完畢后正常關閉，出現膠水滲漏，這是因為配置的針頭太小，影響液體的流動造成背壓。
Glue leakage occurs when the glue dispenser is in use: the dispensing valve is normally closed after use, and glue leakage occurs, because the configured needle is too small, which affects the flow of liquid and causes back pressure.
打膠機流速太慢：膠水流速若太慢主要是膠管過窄或者過長，當然還要注意出膠口和氣壓是不是處于正常情況。
The flow rate of glue dispenser is too slow: if the flow rate of glue is too slow, the main reason is that the rubber hose is too narrow or too long. Of course, pay attention to whether the glue outlet and air pressure are normal.
濟南雙組份打膠機設備出膠量大小不一致：出膠量大小不一致的情況主要是儲存膠水流體的壓力筒還有機器配置空氣壓力不穩定所產生。
The glue output of Jinan two-component gluing machine is inconsistent: the inconsistent glue output is mainly caused by the pressure cylinder storing glue fluid and the unstable air pressure of the machine configuration.
為什么會(huì )出問題？日積月累正常的使用磨損；錯誤操作造成系統癱瘓等等原因，以上的故障使用者需要提前了解到，并做好相關的預防措施，更多相關內容就來我們網站
http://www.sdxfsljx.com咨詢了解吧。
Why is something wrong? Wear and tear in normal use over time; Users of the above failures need to know in advance about the causes of system paralysis caused by incorrect operation, and take relevant preventive measures. For more relevant content, please come to our website http://www.sdxfsljx.com Consult and understand.
上一篇：打膠機的打膠環節和打膠機之間的關系
下一篇：打膠機檢修小竅門必備技能
