封邊機在日常使用過程中如何維護及保養？
封邊機可以效率更高更準確的對進行直線封邊、修邊以及拋光等作業，但是有很多人在使用全自動封邊機的過程中，忽略了封邊機的保養維護工作。盡管保養維護可能會(huì )耗費一定的人力物力，但是卻能延長機器的使用壽命，提高工作效率，因此對機器保養維護是很重要的。如果封邊機日常使用頻繁而維護不到位的話，久而久之會(huì )導致封邊機設備的提前老化，從而縮短使用壽命，所以封邊機的日常護理及定期維護是必不可少的，維護及保養封邊機主要有以下幾點基礎操作：
The edge banding machine can perform straight-line edge banding, trimming and polishing with higher efficiency and more accuracy, but many people ignore the maintenance of the edge banding machine in the process of using the full-automatic edge banding machine. Although maintenance may consume a certain amount of human and material resources, it can prolong the service life of the machine and improve work efficiency. Therefore, it is very important for machine maintenance. If the edge banding machine is frequently used and the maintenance is not in place, over time, it will lead to the early aging of the edge banding machine equipment, so as to shorten the service life. Therefore, the daily care and regular maintenance of the edge banding machine are essential. The maintenance and maintenance of the edge banding machine mainly include the following basic operations:
封邊機控制面板
Edge banding machine control panel
1.定期潤滑：對封邊機各個部件軸承加潤滑油進行潤滑，并且一定要選擇適當的潤滑油，否則也會(huì )對封邊機的正常使用有影響。
1. Regular lubrication: lubricate the bearings of all parts of the edge banding machine with lubricating oil, and be sure to select appropriate lubricating oil, otherwise it will also affect the normal use of the edge banding machine.
2.定期檢查：定期對全自動封邊機進行檢查維護，在維護過程中要仔細查看齒輪、軸承等零件的一些磨損情況，并及時更換磨損嚴重的零件，一旦發現立即緊固，必要時應該更換螺絲。
2. Regular inspection: the full-automatic edge banding machine shall be inspected and maintained regularly. During the maintenance process, it is necessary to carefully check some wear conditions of gears, bearings and other parts, and replace the seriously worn parts in time. Once found, it shall be fastened immediately, and the screws shall be replaced if necessary.
3.及時清理：清理生產過程中產生的木屑以及各種雜物，防止以上的廢料堆積造成機器卡頓，影響機器的正常使用，其次要及時清理機器表面的一些污漬，保持封邊機的整潔，也防止有害物質對機身表面造成腐蝕損壞。
3. Timely cleaning: clean up the sawdust and various sundries produced in the production process to prevent the above waste accumulation from causing the machine to jam and affecting the normal use of the machine. Secondly, clean up some stains on the surface of the machine in time to keep the edge banding machine clean and prevent the corrosion damage of harmful substances to the surface of the machine body.
4.及時清理：清清理邊機周?chē)膹U料，保持操作區域的干凈。
4. Timely cleaning: clean the waste around the edge machine and keep the operation area clean.
5.涂膠量的大小及使用溫度的高低應根據工件的厚度、寬窄和大小,以及封邊機本身的能力來做出相應的調節。
5. The gluing amount and service temperature shall be adjusted according to the thickness, width and size of the workpiece and the capacity of the edge banding machine itself.
6.定期清理膠鍋：防止長期高溫加熱形成積碳，影響設備正常加熱效果。
6. Clean the glue pot regularly: prevent carbon deposition caused by long-term high-temperature heating and affect the normal heating effect of the equipment.
7.回膠口應保持通順：否則工件的下口會(huì )很臟，從而影響質量，同時，膠也會(huì )附在輸送帶和行程開關上，造成行程開關誤動作而損壞工件和設備。
7. The glue return port shall be kept smooth: otherwise, the lower port of the workpiece will be very dirty, which will affect the quality. At the same time, the glue will also be attached to the conveyor belt and travel switch, resulting in misoperation of the travel switch and damage to the workpiece and equipment.
封邊雖小，但也不可忽視
Although the edge banding is small, it can not be ignored
The wonderful content of this article is provided by Jinan two-component gluing machine. There are many wonderful contents on this website. You can click to enter more contents: http://www.sdxfsljx.com We have special customer service to answer your questions
上一篇：關于雙組份打膠機的清洗方法
下一篇：雙組份打膠機安裝的順序是怎樣的？
