野花社区www中文_野花社区最新_野花社区www高清在线观看_野花社区视频最新资源下载_野花影视大全在线观看免费高清6_野花社区www视频最新资源_野花影视大全在线观看_野花社区在线观看免费完整版www

你現在的位置:首頁>企業動態

怎樣調試臥式中空玻璃半自動打膠機

瀏覽:0
一、中空玻璃自動打膠機的原理和構造
1、 Principle and structure of insulating glass automatic gluing machine
中空玻璃自動打膠機是玻璃深加工設備中產生較晚但用量較大的機械設備之一。,主要作用是將半成品的中空玻璃做好密封,也可以作異形玻璃的密封。正確合理的使用中空玻璃自動打膠機,不僅能保證生產的正常進行,還會(huì )起到延長機器壽命的作用。中空玻璃打膠機總共分為三種:立式自動打膠機、臥式半自動打膠機、手動打膠機。
Insulating glass automatic gluing machine is one of the mechanical equipment with late production but large consumption in glass deep processing equipment., The main function is to seal the semi-finished insulating glass, and it can also be used as the sealing of special-shaped glass. The correct and reasonable use of insulating glass automatic gluing machine can not only ensure the normal production, but also prolong the service life of the machine. There are three types of insulating glass glue applicators: vertical automatic glue applicator, horizontal semi-automatic glue applicator and manual glue applicator.
中空玻璃半自動打膠機主要通過打膠機來實現中空玻璃的打膠??蛻?hù)可以根據自己需要的參數來設置中空玻璃半自動打膠機。
The semi-automatic gluing machine for insulating glass mainly realizes the gluing of insulating glass through the gluing machine. Customers can set the semi-automatic gluing machine for insulating glass according to their own parameters.
臥式中空玻璃半自動打膠機通產是由打膠機、供膠機組成。每個廠家的不盡相同,因為不同的材料和電機會(huì )影響機器的精度和使用壽命。通常中空玻璃半自動打膠機的壽命為10—15年。
Horizontal insulating glass semi-automatic gluing machine is composed of gluing machine and glue supply machine. The prices of each manufacturer are different, because different materials and motors will affect the accuracy and service life of the machine. Generally, the service life of insulating glass semi-automatic gluing machine is 10-15 years.
二、怎樣調試臥式中空玻璃半自動打膠機
2、 How to debug horizontal insulating glass semi-automatic gluing machine
放在一個平整干凈的平面上,連接電源和氣源,兩者確認接通之后就開始進行操作。打開氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,然后在顯示屏上找到原點設定,點擊輔助原點設定,然后點擊頭部原點設定,注意原點設定時避免頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定,先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度,輸入完以后,點擊設置進入。等命令位置和當前位置數值一致即可,注意設置時傳送帶上不要有玻璃。然后是混交了,按一桶膠按鈕,按工作選擇按鈕,然后按拍膠啟動,在按伐開,此時膠頭以出膠,等看不見白膠,以混均勻以后按伐關,在按鏈接生產線,自動,自動運行,此時可以自動打膠。
Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected. First turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer, and then the glass thickness. After entering, click the setting to enter. Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting. Then it is mixed. Press a bucket of glue button, press the work selection button, and then press the glue shooting button to start. When you press cutting on, the glue head will release the glue. When you can't see the white glue, press cutting off after mixing evenly. When you press the link production line, it will run automatically and automatically. At this time, you can apply glue automatically.
調試的注意事項:
Precautions for commissioning:
1、 在當天機器操作完畢后要把膠管內的膠沖出,防止硬化;如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on the same day, the rubber in the rubber hose shall be washed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the hose and gun with kerosene.
2、 雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高,低質量的膠容易堵塞膠管的過濾系統,造成出膠不暢或不均勻。
2. For the silicone glue or polysulfide glue used in the two-component gluing machine, attention shall be paid to that the impurities shall not be too high. The low-quality glue is easy to block the filtering system of the hose, resulting in poor or uneven glue delivery.
3、 在更換膠的品種時要特別注意把雙組份打膠機內殘留的膠沖凈,行清洗,因為不同品種甚的膠容易反應堵塞機器。
3. When changing the type of glue, pay special attention to flush the residual glue in the two-component gluing machine and clean it first, because different types and even brands of glue are easy to react and block the machine.
液壓站系統的壓力,不能調的太高,要根據室內環境溫度等實際情況,調滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍?zhuān)駝tB組份管路壓力將升得很高,造成事故。
The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as indoor ambient temperature, adjust it to meet the normal glue output of the glue nozzle and apply glue evenly. When opening the hydraulic station, be sure to open the glue gun, otherwise the pressure of component B pipeline will rise very high, resulting in accidents.
本文由雙組份打膠機為您提供,我們的網站是:http://www.sdxfsljx.com我們將以全心全意的熱情為您提供服務,歡迎您的訪問!
This article is provided by the two-component glue applicator. Our website is: http://www.sdxfsljx.com We will serve you with wholehearted enthusiasm. Welcome to visit!

上一篇:挑選自動點膠機的技能了解一下
下一篇:雙組份密封膠的固化時需要注意那些事項?

  • 微信