雙組份打膠機的注意事項跟操作指南
雙組份打膠機注意事項
Precautions for two-component glue applicator
1. 由于雙組份密封膠的固化需要一定的時間，已涂覆雙組份密封膠的玻璃應緩慢水平移動。
1. Since the curing of two-component sealant takes a certain time, the glass coated with two-component sealant shall move slowly and horizontally.
2. A組和B組膠水應保持清潔，防止異物進入膠水。
2. Group A and group B glues shall be kept clean to prevent foreign matters from entering the glue.
3.在連續工作過程中，膠槍每次停止工作一般不應超過20分鐘，否則用A組份膠將混合的膠全部沖出，直到從槍口排出一根A組份膠為止。
3. During continuous operation, the glue gun shall not stop working for more than 20 minutes each time, otherwise all the mixed glue shall be washed out with component a glue until a component a glue is discharged from the muzzle.
4. 嚴禁強行擠壓或彎曲高壓軟管，以免影響系統的正常運行。
4. It is forbidden to forcibly squeeze or bend the high-pressure hose to avoid affecting the normal operation of the system.
5. 混膠機應始終保持通暢，以保證良好的出膠效果。如有堵塞，可在丙酮中浸泡后清洗。建議每5組清洗一次。
5. The mixer shall always be kept unobstructed to ensure good glue output effect. If it is blocked, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.
6. 當膠槍長時間不使用(超過一周)時，應將膠槍本體拆下，用溶劑清洗膠槍和混膠機內的殘余膠。
6. When the glue gun is not used for a long time (more than one week), remove the glue gun body and clean the residual glue in the glue gun and mixer with solvent.
7. 不同的雙組份膠水廠家生產的膠水中雜質的量是不同的。根據實際情況，b組過濾器和單向止回閥通暢。建議每?jì)山M清洗一次。
7. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, group B filter and one-way check valve are unobstructed. It is recommended to clean every two groups.
8. 因膠水凝固而引起的膠槍、管道或整機故障，不保修。
8. Failure of glue gun, pipeline or whole machine caused by glue solidification shall not be guaranteed.
9. 定期對各油泵加油口進行加油，確保注油器中有連續的油。
9. Fill the oil filler of each oil pump regularly to ensure that there is continuous oil in the oiler.
雙組份打膠機操作
Two component gluer operation
1.連接氣源:
1. Connect the air source:
打開電源，調節減壓閥0.4~0.6Mpa，檢查系統是否有泄漏。然后試運行以下動作:(1)泵A舉升;(2)泵A充氣;(3) B泵提升;(4) B泵充氣。注:升油缸升起時，若兩缸不同步，請降原點重新操作。
Turn on the power supply, adjust the pressure reducing valve to 0.4 ~ 0.6MPa, and check the system for leakage. Then test run the following actions: (1) pump a lifting; (2) Pump a inflates; (3) B pump lifting; (4) B pump inflation. Note: when the lift cylinder rises, if the two cylinders are not synchronized, please drop to the origin and operate again.
2.將A、B部件膠桶放置到位，并與A、B膠泵軸線對齊。
2. Place the rubber barrels of parts A and B in place and align them with the axis of rubber pumps a and B.
以A組件為例:
Take component A as an example:
1)作手動閥將A泵升高點。在吊裝過程中，觀察管路是否拉伸過緊。
1) Use manual valve to raise pump a to high point. During hoisting, observe whether the pipeline is stretched too tightly.
2)將膠桶置于A(yíng)泵的壓膠板下，打開膠桶，將膠袋從膠桶中翻出，取出塑料片。
2) Place the rubber barrel under the rubber pressing plate of pump a, open the rubber barrel, turn out the rubber bag from the rubber barrel and take out the plastic sheet.
3)緩慢降低A泵的壓板。壓板放入桶內時，應與桶口對準，打開壓膠板的排氣口，直壓膠板接觸橡膠面。當壓板內的氣體全部排出，少量膠水從排氣口溢出時，可關閉排氣閥。(升降機開關仍按下)
3) Slowly lower the pressure plate of pump a. When the pressing plate is put into the barrel, it shall be aligned with the barrel mouth, and the exhaust port of the rubber pressing plate shall be opened until the rubber pressing plate contacts the rubber surface. When all the gas in the pressing plate is discharged and a small amount of glue overflows from the exhaust port, the exhaust valve can be closed. (lift switch still pressed)
4)開機試膠:打開主泵氣源開關，按下膠槍開關，待A泵的空氣從槍口排出后停止，繼續上膠
4) Start up and glue test: turn on the air source switch of the main pump, press the glue gun switch, stop after the air of pump a is discharged from the muzzle, and continue to glue
用同樣的方法操作泵B。
Operate pump B in the same way.
3.上膠操作:
3. Gluing operation:
1)松開比例桿上的比例泵鎖緊螺桿，將比例泵的內外調節到所需的比例。只有當A膠和B膠的配比達到正常值時，才能進行以下操作。
1) Loosen the locking screw of the proportional pump on the proportional rod and adjust the inside and outside of the proportional pump to the required proportion. The following operations can be carried out only when the ratio of glue a and glue B reaches the normal value.
2)設置在A(yíng)和B泵選擇器旋鈕,調整噴膠槍出口縫的兩塊玻璃,打開噴膠槍開關,把膠槍在適當的速度,以便順利的雙組分膠玻璃槽填滿,填滿。好。涂完膠后關閉噴膠槍。
2) Set the selector knob of pump a and pump B, adjust the two pieces of glass at the outlet seam of the glue gun, turn on the glue gun switch, and keep the glue gun at an appropriate speed so that the two-component glue glass tank can be filled smoothly. OK. Close the glue gun after coating.
4.更換塑料桶:
4. Replace the plastic bucket:
1)當膠桶內膠水用完時，應立即關閉開關A、B，停止點膠。
1) When the glue in the glue barrel is used up, switch off switches a and B immediately and stop dispensing.
2)打開A(或B)橡膠泵充氣開關，將A(或B)橡膠泵起升機構選為上位，輕觸旋鈕，使壓力板緩緩抬起。此時應注意:盡量不要將膠桶離開底盤，直到壓板與膠桶完全分離后，才關閉A(或B)膠泵的充氣開關。
2) Turn on the inflation switch of a (or b) rubber pump, select the lifting mechanism of a (or b) rubber pump as the upper position, and gently touch the knob to lift the pressure plate slowly. Note at this time: try not to leave the rubber barrel from the chassis until the pressing plate is completely separated from the rubber barrel, and then turn off the inflation switch of a (or b) rubber pump.
具體操作:關閉B泵，打開B回膠開關，再打開膠槍?zhuān)蹦z條呈白色。
Specific operation: turn off pump B, turn on the glue return switch B, and then turn on the glue gun until the glue strip is white.
一起來了解一下雙組份打膠機操作步驟
Let's learn about the operation steps of two-component glue applicator
The wonderful content of this article is provided by Jinan two-component gluing machine. There are many wonderful contents on this website. You can click to enter more contents: http://www.sdxfsljx.com We have special customer service to answer your questions
上一篇：雙組份打膠機打膠不滿是什么原因導致的？
下一篇：雙組份打膠機有哪些性能特點
