雙組份打膠機?主要技術參數是什么？
雙組份打膠機由A、B膠泵、氣動體系、升降安排、機架等組成。詳細介紹如下：
The two-component glue applicator is composed of a and B glue pumps, pneumatic system, lifting arrangement, frame, etc. Details are as follows:
1、膠泵：
1. Rubber pump:
(1)A、B組份各設一個膠泵，在各自的氣馬達驅動下，分別作往復運動，將膠吸入并壓出。A、B膠泵分別與壓膠盤固定在一起，再與機架聯接組成各自的體系。
(1) Components a and B are respectively equipped with a rubber pump, which is driven by their respective air motors to make reciprocating motion to suck in and press out the rubber. A. B glue pump is respectively fixed with the glue pressing plate, and then connected with the frame to form their own system.
(2)A、B組份的配比是通過比例杠桿進行調度：向里調度，B出膠量減少，向外調度，B出膠量增加。通過調度比例杠桿來操控B膠的出膠量，然后操控A、B膠的配比。
(2) The proportioning of components a and B is scheduled through the proportional lever: when scheduling inward, the glue output of B decreases, and when scheduling outward, the glue output of B increases. Adjust the proportional lever to control the glue output of glue B, and then control the ratio of glue a and B.
(3)出膠量：由氣源處理器操控，逆時針調度，出膠量增加，順時針調度出膠量減小。雙組份打膠機的膠泵通過比例杠桿調度A、B膠量配比，具有操作靈活，性能安穩，調度規劃大等特點。
(3) Glue output: controlled by the air source processor and scheduled counterclockwise, the glue output increases and decreases when scheduled clockwise. The glue pump of the two-component glue applicator regulates the proportion of a and B glue through the proportional lever, which has the characteristics of flexible operation, stable performance and large scheduling planning.
2、升降安排：
2. Lifting arrangement:
雙組份打膠機的A、B組份膠泵分別設一套氣動升降安排，該升降安排分別由兩個氣缸并聯組成，并通過橫梁固定聯接各自的泵體。其目的之一是將兩缸的作用力通過壓盤作用在膠面上，壓力大小由調壓閥調度，一般調整在0.3MPa左右;
The A and B component glue pumps of the two-component glue applicator are respectively provided with a set of pneumatic lifting arrangement, which is composed of two cylinders in parallel, and their respective pump bodies are fixedly connected through the beam. One of its purposes is to act the force of the two cylinders on the rubber surface through the pressure plate. The pressure is regulated by the pressure regulating valve and generally adjusted at about 0.3MPa;
雙組份打膠機主要技術參數：
Main technical parameters of two-component glue applicator:
類型：GT04
Type: gt04
混合比：6:1-14:1
Mixing ratio: 6:1-14:1
基料桶：55加侖(20L)
Base barrel: 55 gallons (20L)
較大耗氣：0.5立方米
Large gas consumption: 0.5 M3
擠膠較大工作壓力：20Mpa
Large working pressure for rubber extrusion: 20MPa
供氣壓力：0.5-0.8Mpa
Air supply pressure: 0.5-0.8mpa
外形尺寸：1100*950*2500mm。
Overall dimension: 1100 * 950 * 2500mm.
上一篇：分析硅膠點膠機對封裝環境有什么要求？
下一篇：密封膠對于打膠機的重要性！
