玻璃清洗機的風干系統是如何工作的?
玻璃清洗機的全稱其實就是臥式玻璃清洗干燥機，前段是用水和毛刷達到清洗干凈的目的，后段先經過海綿輥，吸一下玻璃上的水珠，后一步是風機連接的風刀，對玻璃兩面進行吹干，一般來說，風機入口是有加熱棒的，保證進入的空氣是熱風，對吹干玻璃有幫助。
The full name of the glass cleaning machine is actually the horizontal glass cleaning dryer. In the front section, water and brush are used to achieve the purpose of cleaning. In the later section, the sponge roller is used to absorb the water droplets on the glass. In the later step, the air knife connected to the fan is used to dry both sides of the glass. Generally speaking, there is a heating rod at the inlet of the fan to ensure that the incoming air is hot air, It is helpful to blow dry the glass.
那么，玻璃清洗機的風干系統就一面了然了，風機入口的加熱棒到風機，再到風刀，將風吹出。
Then, the air drying system of the glass washer is clear. The heating rod at the inlet of the fan goes to the fan and then to the wind knife to blow out the wind.
風干系統中，容易出現故障的就是加熱棒了，因為加熱棒里面是加熱絲，容易燒壞，加熱棒如何避免壞掉呢？那就需要在關機的時候，先停電玻璃清洗機的傳送，水泵等工作元件，停掉風加熱后，風機持續工作十到二十分鐘再關閉，這樣就能幫助加熱棒散熱，很好的保護加熱棒的加熱絲。
In the air drying system, the heating rod is prone to failure, because the heating wire in the heating rod is easy to burn out. How can the heating rod avoid damage? When shutting down, first cut off the transmission of the glass washer, the water pump and other working components. After the air heating is stopped, the fan will continue to work for 10 to 20 minutes and then shut down, so as to help the heating rod dissipate heat and protect the heating wire of the heating rod.
這么說起來，保證玻璃清洗機的風干系統很簡單，那就是保護加熱棒，是保護加熱絲，如何操作呢，就是停止風加熱后，風機持續運轉10到20分鐘再關閉即可。
In this way, it is very simple to ensure the air drying system of the glass washer, that is, to protect the heating rod and the heating wire. How to operate it is to stop the air heating, and then turn off the fan for 10 to 20 minutes.
上一篇：如何避免雙組份結構膠混合不均勻？
下一篇：分析硅膠點膠機對封裝環境有什么要求？
