點膠機常見故障及處理方法
點膠機主要分為半自動點膠機、自動點膠機和全自動點膠機這幾種類型。無論是哪種點膠機，在使用過程中都不可避免的會(huì )為遇到一些小問題。如果客戶能夠分析這些問題的原因并找到解決辦法，他們就可以更順利地使用使用點膠設備，大大的減少客戶找人員解決問題的時間。下面，將為大家介紹一些壓盤泵點膠機使用過程中常見的故障原因分析及解決方法。
Dispensing machine is mainly divided into semi-automatic dispensing machine, automatic dispensing machine and automatic dispensing machine. No matter what kind of dispenser, in the use of the process will inevitably encounter some small problems. If customers can analyze the causes of these problems and find solutions, they can use dispensing equipment more smoothly, greatly reducing the time for customers to find professionals to solve problems. Next, we will introduce some common fault cause analysis and solutions in the use of dispensing machine.
一、點膠機流體內有氣泡的原因及解決辦法
1、 Causes and solutions of bubble in dispensing machine fluid
原因：
reason:
點膠機由于過大的流體壓力和加上過短的開閥時間，會(huì )有可能將空氣滲入液體內，造成氣泡的產生。
Due to excessive fluid pressure and short valve opening time, air may seep into the liquid and cause bubbles.
解決方法：
resolvent:
降低流體壓力并使用錐形斜式針頭。
Reduce fluid pressure and use a tapered, oblique needle.
二、點膠機出膠大小不一致
2、 Dispensing machine glue size is not consistent
原因：
reason:
點膠機儲存流體的壓力筒或空氣壓力不穩定，導致出膠不均勻，大小不一致。
The pressure cylinder or air pressure of the dispenser storing fluid is unstable, resulting in uneven glue output and inconsistent size.
解決方法：
resolvent:
應避免使用壓力介于壓力表之中低壓力部分。膠閥控制壓力應少60psi以上以確保出膠穩定。 后應檢查出膠時間，若小于15/1000秒會(huì )造成出膠不穩定，出膠時間越長出膠越穩定。
The low pressure part of the pressure gauge should be avoided. The control pressure of the rubber valve should be at least 60 psi to ensure stable glue delivery. After that, the glue out time should be checked. If it is less than 15 / 1000 seconds, it will lead to the instability of the glue. The longer the glue time is, the more stable the glue will be.
三、點膠無法停膠
3、 Unable to stop dispensing
原因：
reason:
1.點膠閥中轉桿或密封裝置磨損
1. The transfer rod or sealing device of dispensing valve is worn
2.點膠閥的氣壓是否斷開。
2. Whether the air pressure of dispensing valve is disconnected.
解決辦法：定期檢查設備，更換磨損設備。
Solution: check the equipment regularly and replace the worn equipment.
在使用點膠機時，如果客戶遇到上述故障，建議根據上述分析檢查故障原因，進行處理。如果遇到同樣的情況，可以根據有關方法進行求解，應能大大節省了時間。
When using the dispenser, if the customer encounters the above failure, it is recommended to check the cause of the failure according to the above analysis and deal with it. If the same situation is encountered, it can be solved according to the relevant methods, which should save a lot of time.
上一篇：影響自動點膠機膠體粘度的原因
下一篇：壓盤泵打膠機如何控制膠量？
