野花社区www中文_野花社区最新_野花社区www高清在线观看_野花社区视频最新资源下载_野花影视大全在线观看免费高清6_野花社区www视频最新资源_野花影视大全在线观看_野花社区在线观看免费完整版www

你現在的位置:首頁>企業動態

雙組份打膠機使用過程中遵循的規定

瀏覽:0
1、在全自動雙組份打膠機工作中一般運用的膠水大概有硅膠、瞬間膠、厭氧膠、環氧樹脂、UV膠。
1. In the automatic two-component gluing machine, the general use of glue is about silica gel, instant glue, anaerobic adhesive, epoxy resin, UV glue.
2、真空回吸閥必需求安裝在全自動點膠機上,因為真空回吸功用是防止點膠機中的膠水在不點膠時還在滴漏。
2. The vacuum suction valve must be installed on the automatic dispenser, because the vacuum suction function is to prevent the glue in the dispenser from dripping when not dispensing.
3、點膠量的巨細是由全自動雙組份打膠機在點膠進程中繼續的時間長短來抉擇的,可以確保有滿意的膠水來粘合部件,一同可以防止膠水過多而形成的資源糟蹋。
3. The size of the dispensing amount is determined by the length of time that the automatic two-component dispenser continues in the dispensing process, which can ensure that there is satisfactory glue to bond the parts, and can prevent resource waste caused by excessive glue.
4、固化要素:關于膠水的固化,一般出產廠家已給出溫度曲線。一般在常溫下都可以固化,在實踐應盡可能選用較高溫度來固化,使膠水固化后有滿意強度和硬度。
4. Curing elements: about the curing of glue, the general manufacturer has given the temperature curve. Generally, it can be cured at normal temperature. In practice, higher temperature should be selected as far as possible to make the glue have satisfactory strength and hardness after curing.
5、針頭的標準與類別:針頭的標準會(huì )影響點膠機在點膠進程中出膠的巨細和精密度,當氣壓在必定規劃時,針頭的咀越大,出膠率就越大,所以要依據點膠機在出產出來產品的巨細來定位點膠針頭的標準,一般針頭內徑長度保持在膠點直徑的一半,作用才是更好。
5. Standard and category of needle: the standard of the needle will affect the size and precision of the dispensing machine in the dispensing process. When the air pressure is in a certain planning, the larger the nozzle of the needle is, the greater the glue output rate will be. Therefore, it is necessary to locate the dispensing needle standard according to the size of the product produced by the dispenser. Generally, the inner diameter of the needle should be kept at half of the diameter of the glue point.
6、氣泡關于全自動雙組份打膠機在進行點膠進程中會(huì )影響產品質量,所以膠水放進去之前決對不能有氣泡.如果有氣泡就會(huì )形成點膠機出產出來的產品有許多次品,在運用中要排出膠水的空氣,以防止出現全自動點膠機空打現象。
6. Bubble about the full-automatic two-component dispenser in the dispensing process will affect the product quality, so there must be no bubble before the glue is put in. If there are bubbles, there will be many defective products produced by the dispenser. During the operation, the air of glue should be discharged to prevent the phenomenon of empty tapping of automatic dispensing machine.
7、壓力的巨細直接影響了供膠量和膠水流出的速度,膠水的流動性越差它就越稠,全自動雙組份打膠機需求的壓力就越大,所以咱們應該依據全自動點膠機在出產進程中的環境溫度以及點膠量的巨細和膠水的特性來調度壓力的巨細,全自動點膠機的壓力巨細是經過它內部的調壓閥來進行調度的。
7. The size of the pressure directly affects the amount of glue supplied and the speed of glue outflow, The worse the fluidity of the glue, the thicker it will be, and the greater the pressure required by the automatic two-component gluing machine. Therefore, we should adjust the pressure according to the ambient temperature of the automatic dispenser in the production process, the size of the dispensing amount and the characteristics of the glue. The pressure of the automatic dispenser is regulated through its internal pressure regulating valve.
以上就是關于雙組份打膠機的相關知識介紹,希望能夠幫助到大家。如需了解更多相關資訊,請繼續關注我們網站http://www.sdxfsljx.com后續將呈現更多精彩的內容。
The above is about the two-component glue machine related knowledge introduction, hope to help you. For more information, please stay tuned to our website http://www.sdxfsljx.com More wonderful content will be presented later.

上一篇:雙組份打膠機的注意事項有哪些?
下一篇:液體泡沫對于打膠機有什么影響?

  • 微信