自動打膠機打膠不飽滿的原因有哪些？
一、打膠速度過快導致的
1、 It is caused by too fast gluing speed
有的客戶為了加快自己的生產節奏追趕生產計劃，將打膠速度認為調整的過快，導致膠體還沒有完全達到合格標準機頭就已經移動到下一個位置進行打膠操作了，如果我們需要加快打膠的速度調整了打膠機的移動參數的話，那么我們對應的也應該對供膠系統也進行相應的設置，比如這時候我們就需要加大供膠壓力，增大打膠機的出膠速度來配合對象的移動速度的增加。如果我們僅僅是單獨的增加了打膠機的移動速度而沒有對壓力進行調節的話就很有可能出現打膠不飽滿的情況發生。
In order to speed up the production pace and catch up with the production plan, some customers think that the glue filling speed is adjusted too fast, so that the glue has not completely reached the qualified standard and the head has moved to the next position for glue filling operation. If we need to speed up the glue filling speed and adjust the movement parameters of the glue filling machine, then we should also adjust the glue supply system accordingly Corresponding settings, for example, we need to increase the glue supply pressure, increase the glue delivery speed of the dispenser to match the increase of the moving speed of the object. If we only increase the speed of the dispenser independently without adjusting the pressure, it is likely to occur that the dispenser is not full.
二、供膠壓力不足
2、 Insufficient glue supply pressure
這個情況其實小編在種情況的已經進行過描述了，即便你沒有對打膠機的移動速度進行調節也出現了打膠不飽滿的情況，那么也有可能是供膠壓力過小導致的。這時候我們僅僅需要調整供膠壓力即可的解決這個問題的發生。
In fact, this situation has been described in the first case. Even if you do not adjust the movement speed of the dispenser, there is also a case of insufficient dispensing, which may be caused by too little pressure of glue supply. At this time, we just need to adjust the glue supply pressure to solve this problem perfectly.
三、機頭感應器損壞
3、 Head sensor damaged
這種情況非常的少見，但是也不排除這種情況的發生。在我們的打膠機機頭有一個對鋁條深淺進行探測的感應器，如果發現鋁條過深或者過淺的時候他會(huì )自動的調整移動的移動速度以及供膠壓力（自動調整幅度是小范圍內的）。如果我們的鋁條本身就深淺不一，在加上我們的感情器損壞的壞就會(huì )發生這種情況！
This kind of situation is very rare, but it can not be ruled out. There is a sensor to detect the depth of aluminum strip in our dispenser head. If the aluminum strip is too deep or too shallow, it will automatically adjust the moving speed and glue supply pressure (the automatic adjustment range is small). If our aluminum bars are different in depth, this will happen when our emotional organs are damaged!
上一篇：合適點膠機是如何選擇出來的?
下一篇：點膠機的針頭與膠水使用時應該注意啥？
