中空玻璃膠機的調試方法？
中空玻璃在制作的過程中,有一個鏈接是非常重要的,是使用的結構膠將兩玻璃玻璃完全密封,因為人造膠是緩慢的,封閉的壞,所以大量的中空玻璃的生產需要中空玻璃膠機、下一個帶你去了解中空玻璃膠機的調試方法
In the process of making hollow glass, it is very important to have a link. The structural glue is used to completely seal the two glass glasses. Because the artificial glue is slow and the seal is broken, a large number of hollow glass production needs hollow glass glue machine. The next one will take you to the debugging method of hollow glass glue machine
1,個開關泵的中空玻璃膠機、電源開關、控制開關、控制臺根據手動按鈕,然后在顯示屏找到原點,點擊輔助的起源集,然后單擊設置原點,注意原點時設置為避免碰撞頭部和輔助吸盤。設置后返回設置玻璃的厚度，輸入后，點擊設置進入。命令，如位置與當前位置值是一致的
1. The hollow glass glue machine, power switch, control switch and console of the first switch pump are set according to the manual button, then find the origin on the display screen, click the auxiliary origin set, and then click to set the origin. Note that the origin is set to avoid collision with the head and auxiliary suction cup. After setting, return to set the thickness of glass. After input, click set to enter. Command, such as position is consistent with current position value
2. 打開個膠桶按鈕，按下工作選項拍膠開始，然后按下切割
2. Open the first rubber barrel button, press the work option to start tapping, and then press the cut button
3、如果需要調節膠機壓力，可以點擊屏幕返回尋找密封配方，顯示當前的密封壓力，如果每邊都缺膠，那么可以增加壓力，壓力量大的膠，壓力量小的膠。如果發現某邊膠量不夠，就會(huì )在密封公式中顯示已封好，上封、下封、下封，開始將邊膠封好，然后從上往下訂單
3. If you need to adjust the pressure of the glue machine, you can click the screen to return to find the sealing formula and display the current sealing pressure. If each side is short of glue, you can increase the pressure. Glue with large pressure and glue with small pressure can be used. If it is found that there is not enough adhesive on one side, it will be shown in the sealing formula that it has been sealed. Seal up, seal down and seal down, start to seal up the adhesive on the side, and then order from top to bottom
4. 如果某邊只有少量或大量的膠，稍微調整一下膠的掃描量，量大的膠量大，量少的膠量小
4. If there is only a small amount or a large amount of glue on one side, slightly adjust the scanning amount of glue. The large amount of glue is large, and the small amount of glue is small
上一篇：點膠機的針頭與膠水使用時應該注意啥？
下一篇：中空玻璃打膠機配件鏈接方法！
