野花社区www中文_野花社区最新_野花社区www高清在线观看_野花社区视频最新资源下载_野花影视大全在线观看免费高清6_野花社区www视频最新资源_野花影视大全在线观看_野花社区在线观看免费完整版www

　　When the three-axis dispensing machine is working, there will be inefficient or ineffective dispensing, so how can this phenomenon be caused?

　　A:點膠壓力方面，通常壓力太大易造成膠水溢出、膠量過多；壓力太小則會(huì )出現點膠斷續現象和漏點，從而導致產品缺陷，所以需要根據環境溫度和膠水粘度等因素進行調節。

　　A: In the aspect of dispensing pressure, it is easy to cause glue overflow and excessive glue volume when the pressure is too high. If the pressure is too low, the phenomenon of discontinuous dispensing and leakage point will appear, which will lead to product defects. Therefore, it is necessary to adjust the dispensing pressure according to environmental temperature and glue viscosity and other factors.

　　B:三軸點膠機針頭通常要選取針頭內徑大小為點膠膠點直徑的1/2左右的針頭，點膠過程中，應根據產品大小來選取點膠針頭。

　　B: The needle of a three-axis dispensing machine usually needs to select a needle whose inner diameter is about 1/2 of the diameter of the dispensing point. In the dispensing process, the needle should be selected according to the size of the product.

　　C:針頭與工作面之間的距離，不同的三軸點膠機采用不同的針頭，有些針頭有一定的止動度，因此需要把握好點膠距離，甚每次工作開始之前應做針頭與工作面距離的校準，即Z軸高度校準。膠水的粘度直接影響點膠的質量，粘度大，則膠點會(huì )變小，甚拉絲；粘度小，膠點會(huì )變大，進而可能滲染產品，而膠水溫度應為23℃～25℃；環境溫度對膠水的粘度影響，溫度降低粘度增大，出膠流量相應變小，更容易出現拉絲現象。

　　C: The distance between the needle and the working face, different three-axis dispensing machines use different needles, some needles have a certain degree of stiffness, so it is necessary to grasp the dispensing distance, and even before each start of work, the distance between the needle and the working face should be calibrated, that is, Z-axis height calibration. Viscosity of glue directly affects the quality of dispensing, and if the viscosity is high, the glue point will become smaller or even wire drawing; if the viscosity is low, the glue point will become larger, and then the product may be dyed, while the glue temperature should be 23 ~25 C; when the ambient temperature affects the glue viscosity, the temperature decreases and the viscosity increases, and the flow rate of glue decreases accordingly, which makes the filament drawing easier.